triax icp® force sensor, 45 n (10.1 lb) all axes, 110 mv/n, metric mounting

3-Component ICP® Force Sensor

Model 260M36

Retrieving Price...

(Pricing valid only in the U.S.)

Units in Stock Lead Times
More on the way Call for Lead Time
  • CE
  • IP

Triax ICP® force sensor, 45 N (10.1 lb) all axes, 110 mV/N, metric mounting

  • Temperature Range: -65 to +250 °F (-54 to +121 °C)
  • Electrical Connector: 4-Pin

Specification Notes


[1] Zero-based, least-squares, straight line method.
[2] Sensitivites are for listed preload. Sensitivites may vary ±5% depending on preload used.
[3] Sensitivities are dependent upon supplied bolt.
[4] Typical.
[5] Perform in steps of 2.5 in-lbs (28 N cm) to protect electronics (40 V max).
[6] Apply thin layer of lithium grease to sliding surfaces (washer, nut, threads).
[7] See PCB Declaration of Conformance PS023 for details.

English: SI:
Performance
Sensitivity (±20 %) (Z Axis) 490 mV/lb 110 mV/N [2] [3]
Sensitivity (±20 %) (X or Y Axis) 490 mV/lb 110 mV/N [2] [3]
Measurement Range (Z Axis) 10.1 lb 45 N
Measurement Range (X or Y Axis) 10.1 lb 45 N
Maximum Force (Z Axis) 13.5 lb 60 N
Maximum Force (X or Y Axis) 13.5 lb 60 N
Maximum Moment (Z Axis) 14 ft-lb 18.98 Nm
Maximum Moment (X or Y Axis) 13 ft-lb 17.63 Nm
Broadband Resolution (z axis) ≤0.0003 lb-rms ≤0.0013 N-rms
Broadband Resolution (x or y axis) ≤0.0003 lb-rms ≤0.0013 N-rms
Upper Frequency Limit 90000 Hz 90000 Hz
Low Frequency Response (-5 %) (Z-Axis) 0.02 Hz 0.02 Hz
Low Frequency Response (-5 %) (X or Y Axis) 0.01 Hz 0.01 Hz
Non-Linearity ≤1 % FS ≤1 % FS [1]
Cross Talk (between X and Y Axis) ±3 % ±3 %
Cross Talk (between (X or Y Axis) and Z Axis) ±5 % ±5 %
Environmental
Temperature Range -65 to +250 °F -54 to +121 °C
Electrical
Full Scale Output (Z Direction) ±5 VDC ±5 VDC
Full Scale Output (X and Y Direction) ±5 VDC ±5 VDC
Discharge Time Constant (Z Axis) ≥25 sec ≥25 sec
Discharge Time Constant (X or Y Axis) ≥50 sec ≥50 sec
Excitation Voltage (all channels) 20 to 30 VDC 20 to 30 VDC
Constant Current Excitation (all channels) 2 to 20 mA 2 to 20 mA
Output Impedance ≤100 Ohm ≤100 Ohm
Output Bias Voltage 8 to 14 VDC 8 to 14 VDC
Spectral Noise (1 Hz) 300 µlb/√Hz 1350 µN/√Hz [4]
Spectral Noise (10 Hz) 150 µlb/√Hz 670 µN/√Hz [4]
Spectral Noise (100 Hz) 50 µlb/√Hz 230 µN/√Hz [4]
Spectral Noise (1000 Hz) 2.3 µlb/√Hz 10 µN/√Hz [4]
Spectral Noise (10000 Hz) 0.7 µlb/√Hz 3 µN/√Hz [4]
Spectral Noise (1 Hz) 150 µlb/√Hz 670 µN/√Hz [4]
Spectral Noise (10 Hz) 55 µlb/√Hz 250 µN/√Hz [4]
Spectral Noise (100 Hz) 20 µlb/√Hz 90 µN/√Hz [4]
Spectral Noise (1000 Hz) 2.3 µlb/√Hz 10 µN/√Hz [4]
Spectral Noise (10000 Hz) 0.7 µlb/√Hz 3 µN/√Hz [4]
Output Polarity Positive Positive
Physical
Preload Torque 56 in-lb 6.3 Nm [5] [6]
Stiffness (Z Axis) 10 lb/µin 1.75 kN/µm [4]
Stiffness (X or Y Axis) 4 lb/µin 0.7 kN/µm [4]
Size - Height 0.390 in 9.90 mm
Size - Length 1.075 in 27.3 mm
Size - Width 0.95 in 24.1 mm
Size - Bolt Diameter 0.205 in 5.21 mm
Size - ID 0.319 in 8.10 mm
Size - Sensing Surface 0.680 in 17.27 mm
Weight 0.927 oz 26.28 gm
Housing Material Stainless Steel Stainless Steel
Sealing Hermetic Hermetic
Electrical Connector 4-Pin 4-Pin
Electrical Connection Position Side Side

* All specifications are at room temperature unless otherwise specified.

Accessories


Supplied
082B02 Anti-friction washer for Models (M)202B, (M)212B, (M)260A01, (M)260A11 & (M)260A31 1
083A10 Pilot bushing (for Models 260A01, 260A11 & 260A31) 1
M081A70 Pre-load bolt (for Models 260A01, 260A11 & 260A31) 1

Build Out Your Measurement Chain


M081A70
Model: M081A70

Pre-load bolt (for Models 260A01, 260A11...

$67.00 USD

(Pricing valid only in the U.S.)

082B02
Model: 082B02

Anti-friction washer for Models (M)202B,...

$28.00 USD

(Pricing valid only in the U.S.)

083A10
Model: 083A10

Pilot bushing (for Models 260A01, 260A11...

$57.50 USD

(Pricing valid only in the U.S.)