triaxial, miniature (4 gm), ceramic shear icp® accel., 10 mv/g, built-in filter, 5-ft attached cable to 4-socket 1/4-28 plug, no breakout cable

Accelerometer, ICP®, Triaxial

Model 356A61/NC

Triaxial, miniature (4 gm), ceramic shear ICP® accel., 10 mV/g, built-in filter, 5-ft attached cable to 4-socket 1/4-28 plug, no breakout cable

Electrical Filter Corner Frequency: >15 kHz

Sensitivity: (±15%)10 mV/g (1.02 mV/(m/s²))
Measurement Range: ±500 g pk (±4905 m/s² pk)
Frequency Range: (-5%)2 to 4000 Hz
Electrical Connector: Integral Cable

Additional configurations:

Specification Notes

[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] See PCB Declaration of Conformance PS023 for details.

	English:	SI:
Performance
Sensitivity (±15 %)	10 mV/g	1.02 mV/(m/s²)
Measurement Range	±500 g pk	±4905 m/s² pk
Frequency Range (-5 %)	2 to 4000 Hz	2 to 4000 Hz
Resonant Frequency	≥55 kHz	≥55 kHz
Electrical Filter Roll-off	6 dB/octave	6 dB/octave	[2]
Electrical Filter Corner Frequency	15 kHz	15 kHz	[2]
Broadband Resolution (1)	0.008 g rms	0.08 m/s² rms	[2]
Non-Linearity	≤1 %	≤1 %	[1]
Transverse Sensitivity	≤5 %	≤5 %
Environmental
Overload Limit (Shock)	±10000 g pk	±98100 m/s² pk
Temperature Range (Operating)	-65 to +325 °F	-54 to +163 °C
Temperature Response	See Graph %/°F	See Graph %/°F	[2]
Electrical
Excitation Voltage	18 to 30 VDC	18 to 30 VDC
Constant Current Excitation	2 to 20 mA	2 to 20 mA
Output Impedance	≤200 Ohm	≤200 Ohm
Output Bias Voltage	7 to 12 VDC	7 to 12 VDC
Discharge Time Constant	0.3 to 1.0 sec	0.3 to 1.0 sec
Settling Time (within 10% of bias)	≤3.0 sec	≤3.0 sec
Spectral Noise (1 Hz)	445 µg/√Hz	4365 (µm/sec²)/√Hz	[2]
Spectral Noise (10 Hz)	135 µg/√Hz	1325 (µm/sec²)/√Hz	[2]
Spectral Noise (100 Hz)	90 µg/√Hz	883 (µm/sec²)/√Hz	[2]
Spectral Noise (1 kHz)	80 µg/√Hz	785 (µm/sec²)/√Hz	[2]
Physical
Sensing Element	Ceramic	Ceramic
Sensing Geometry	Shear	Shear
Housing Material	Titanium	Titanium
Sealing	Welded Hermetic	Welded Hermetic
Size - Height	0.4 in	10.2 mm
Size - Length	0.4 in	10.2 mm
Size - Width	0.4 in	10.2 mm
Weight (without cable)	0.14 oz	4.0 gm	[2]
Electrical Connector	Integral Cable	Integral Cable
Electrical Connection Position	Side	Side
Cable Termination	1/4-28 4-Pin Jack	1/4-28 4-Pin Jack
Cable Length	5.0 ft	1.5 m
Cable Type	034 4-cond Shielded	034 4-cond Shielded
Mounting	Stud	Stud
Mounting Thread	5-40 Female	5-40 Female
Mounting Torque	4 to 5 in-lb	45 to 56 N-cm

* All specifications are at room temperature unless otherwise specified.

Accessories


Supplied
034G05	4-conductor, low noise, shielded FEP cable, 5-ft, 4-socket plug to (3) BNC plugs (labeled X Y Z)	1
080A	Adhesive mtg base, 0.5" hex x 0.187" thk, 10-32 tapped hole, aluminum w/isolation hardcoat finish	1
080A109	Petro Wax, one square, 1" x 1" x 0.25"	1
081A27	Mounting stud, 5-40 to 5-40 thds, w/o shoulder, BeCu	1
081A90	Mounting stud, 10-32 to 5-40	1
ACS-1T	Triaxial amplitude response calibration, from 10 Hz to upper 5% frequency, NIST traceable	1
M081A27	Metric mtg stud, 5-40 to M3 x 0.50 long	1