icp® quartz force ring, 10 lb comp., 500 mv/lb

Force Sensor, ICP®

Model 201B01

Retrieving Price...

(Pricing valid only in the U.S.)

Units in Stock	Lead Times
More on the way	Lead Time for 1-3 is 5 Wks.

ICP® quartz force ring, 10 lb comp., 500 mV/lb

Measurement Range: 10 lb (0.0445 kN)
Sensitivity: (±15%)500 mV/lb (112405 mV/kN)
Low Frequency Response: (-5%)0.01 Hz
Upper Frequency Limit: 90000 Hz
Temperature Range: -65 to +250 °F (-54 to +121 °C)

Specification Notes

[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] Calculated from discharge time constant.
[4] Estimated using rigid body dynamics calculations.
[2] Typical.
[5] See PCB Declaration of Conformance PS023 for details.

	English:	SI:
Performance
Sensitivity (±15 %)	500 mV/lb	112405 mV/kN
Measurement Range (Compression)	10 lb	0.0445 kN
Maximum Static Force (Compression)	60 lb	0.267 kN
Broadband Resolution (1)	0.0002 lb-rms	0.0008896 N-rms	[2]
Low Frequency Response (-5 %)	0.01 Hz	0.01 Hz	[3]
Upper Frequency Limit	90000 Hz	90000 Hz	[4]
Non-Linearity	≤1 % FS	≤1 % FS	[1]
Environmental
Temperature Range	-65 to +250 °F	-54 to +121 °C
Temperature Coefficient of Sensitivity	≤0.03 %/°F	≤0.054 %/°C
Electrical
Discharge Time Constant (at room temp)	≥50 sec	≥50 sec
Excitation Voltage	20 to 30 VDC	20 to 30 VDC
Constant Current Excitation	2 to 20 mA	2 to 20 mA
Output Impedance	≤100 Ohm	≤100 Ohm
Output Bias Voltage	8 to 14 VDC	8 to 14 VDC
Output Polarity (Compression)	Positive	Positive
Physical
Preload	60 lb	0.267 kN
Stiffness	12 lb/µin	2.1 kN/µm	[2]
Size - Diameter	0.650 in	16.5 mm
Size - Height	0.310 in	7.9 mm
Size - Bolt Diameter	0.25 in	6 mm
Size - ID (Hole Diameter)	0.251 in	6.38 mm
Size - OD (Sensor)	0.650 in	16.51 mm
Size - Sensing Surface	0.50 in	12.7 mm
Weight	0.35 oz	10 gm
Housing Material	Stainless Steel	Stainless Steel
Sealing	Hermetic	Hermetic
Electrical Connector	10-32 Coaxial Jack	10-32 Coaxial Jack
Electrical Connection Position	Side	Side

* All specifications are at room temperature unless otherwise specified.

Accessories


Supplied
080A82	Assembly lubricant (for Series 201-207 force rings)	1
081A11	Mounting stud, 10-32 x 0.730", BeCu for Models 201B01, 201B02, 201B03, 201B04, 201B05, 211B & 201B76	1
082B01	Anti-friction washer for Models 201B01, 201B02, 201B03, 201B04, 201B05 & 211B	1
083B01	Pilot bushing for Models 201B01, 201B02, 201B03, 201B04, 201B05 & 211B	1
M081A11	Mounting stud, M5x0.8 x 0.730", BeCu for Models 201B01, 201B02, 201B03, 201B04, 201B05, 211B & 201B76	1
M083B01	Pilot bushing for Models 201B01, 201B02, 201B03, 201B04, 201B05 & 211B	1